View ISL88001IE31Z-T_4864637.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
ISL88001, ISL88002, ISL88003
Data Sheet March 26, 2008 FN6174.0
Ultra Low Power 3 Ld Voltage Supervisors in SC-70 and SOT-23 Packages
The ISL88001, ISL88002, ISL88003 supervisors are extremely low power 160nA voltage supervisors that help to monitor the power supply voltages in a wide variety of applications. By providing Power-On Reset and supply voltage supervision in small 3 Ld SC-70 and SOT-23 packages, the ISL88001, ISL88002, ISL88003 devices can help to lower system cost, reduce board space requirements and increase the reliability of systems. The most popular voltage trip points are available for standard power supplies from 1.8V to 5.0V (see "Ordering Information" on page 3). These reset threshold voltages are accurate to within 1.2% and the reset signal is valid down to 1V. Active high and active low reset outputs are available in push-pull and open drain configurations (see "Functional Block Diagrams" on page 2). The ISL88001, ISL88002, ISL88003 devices are specifically designed for low power consumption and high threshold accuracy, making them especially suitable for electronic devices and portable equipment.
Features
* Single Voltage Monitoring Supervisors * Fixed-Voltage Options Allow Precise Monitoring of +1.8V, +2.5V, +3.0V, +3.3V and +5.0V Power Supplies * Ultra Low 160nA Supply Current * 1.2% Voltage Threshold Accuracy * 190ms Power-On Reset Timeout * Reset Signal Valid Down to VDD = 1V * No External Components Necessary * Immune to Power-Supply Transients * Available in Small 3 Ld SC-70 and 3 Ld SOT-23 Pb-free Packages * Pin Compatible with MAX803, MAX809, MAX810 * Pb-Free (RoHS Compliant)
Applications
* Microprocessor/Microcontroller Systems * Intelligent Instruments
Pinouts
ISL88001, ISL88002 (3 LD SC-70, 3 LD SOT-23) TOP VIEW
GND 1
* Controllers * Computer Systems * Portable/Battery-Powered Equipment * PDA and Hand-Held PC Devices
ISL88001 ISL88002 3 VDD
RST
2
ISL88001 has a push-pull RST output ISL88002 has an open-drain RST output
ISL88003 (3 LD SC-70, 3 LD SOT-23) TOP VIEW
GND 1
ISL88003
3
VDD
RST
2
ISL88003 has a push-pull RST output
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners.
ISL88001, ISL88002, ISL88003 Functional Block Diagrams
VDD VDD RST POR VREF VDD VREF GND VDD GND
POR
RST
ISL88001
ISL88002
VDD
POR VREF VDD
RST
GND
ISL88003
Pin Descriptions
PIN ISL88001 ISL88002 1 2 2 3 3 ISL88003 1 PIN NAME GND RST RST VDD Ground IC reference. The RST pin is an active-low reset output that is pulled to GND (LOW) when reset is asserted. The ISL88001 is push-pull while the ISL88002 is open drain. The RST pin is a push-pull active-high reset output that is pulled to VDD (HIGH) when reset is asserted. Supply Voltage and Monitored Input. The VDD pin is the IC power supply terminal and also the monitored input. PIN FUNCTION
2
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003 Ordering Information
PART NUMBER (Notes 1, 2, 3) ISL88001IE46Z-T ISL88001IE44Z-T ISL88001IE31Z-T ISL88001IE29Z-T ISL88001IE26Z-T ISL88001IE23Z-T ISL88001IE22Z-T ISL88001IE17Z-T ISL88001IE16Z-T ISL88001IH46Z-T ISL88001IH44Z-T ISL88001IH31Z-T ISL88001IH29Z-T ISL88001IH26Z-T ISL88001IH23Z-T ISL88001IH22Z-T ISL88001IH17Z-T ISL88001IH16Z-T ISL88002IE46Z-T ISL88002IE44Z-T ISL88002IE31Z-T ISL88002IE29Z-T ISL88002IE26Z-T ISL88002IE23Z-T ISL88002IE22Z-T ISL88002IE17Z-T ISL88002IE16Z-T ISL88002IH46Z-T ISL88002IH44Z-T ISL88002IH31Z-T ISL88002IH29Z-T ISL88002IH26Z-T ISL88002IH23Z-T ISL88002IH22Z-T ISL88002IH17Z-T ISL88002IH16Z-T ISL88003IE46Z-T ISL88003IE44Z-T ISL88003IE31Z-T PART MARKING 146 144 131 129 126 123 122 117 116 1H46 1H44 1H31 1H29 1H26 1H23 1H22 1H17 1H16 246 244 231 229 226 223 222 217 216 2H46 2H44 2H31 2H29 2H26 2H23 2H22 2H17 2H16 346 344 331 RESET Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Open Drain RST Push-Pull RST Push-Pull RST Push-Pull RST VTHVDD (V) 4.64 4.38 3.09 2.92 2.63 2.32 2.19 1.67 1.58 4.64 4.38 3.09 2.92 2.63 2.32 2.19 1.67 1.58 4.64 4.38 3.09 2.92 2.63 2.32 2.19 1.67 1.58 4.64 4.38 3.09 2.92 2.63 2.32 2.19 1.67 1.58 4.64 4.38 3.09 TEMPERATURE RANGE (C) -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 PACKAGE 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 PKG. DWG. # P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.049 P3.049 P3.049
3
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003 Ordering Information (Continued)
PART NUMBER (Notes 1, 2, 3) ISL88003IE29Z-T ISL88003IE26Z-T ISL88003IE23Z-T ISL88003IE22Z-T ISL88003IE17Z-T ISL88003IE16Z-T ISL88003IH46Z-T ISL88003IH44Z-T ISL88003IH31Z-T ISL88003IH29Z-T ISL88003IH26Z-T ISL88003IH23Z-T ISL88003IH22Z-T ISL88003IH17Z-T ISL88003IH16Z-T ISL88001/2/3EVAL1Z NOTES: 1. For non-standard voltage trip point versions between 1.5V and 5V in 100mV increments, please contact factory for availability. 2. Add "-TK" suffix for 1000 piece Tape and Reel. Please refer to TB347 for details on reel specifications. 3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. PART MARKING 329 326 323 322 317 316 3H46 3H44 3H31 3H29 3H26 3H23 3H22 3H17 3H16 RESET Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST Push-Pull RST VTHVDD (V) 2.92 2.63 2.32 2.19 1.67 1.58 4.64 4.38 3.09 2.92 2.63 2.32 2.19 1.67 1.58 TEMPERATURE RANGE (C) -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 PACKAGE 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SC-70 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 3 Ld SOT-23 PKG. DWG. # P3.049 P3.049 P3.049 P3.049 P3.049 P3.049 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064 P3.064
Evaluation Platform for ISL88001, ISL88002 and ISL88003
4
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003
Absolute Maximum Ratings
Temperature Under Bias. . . . . . . . . . . . . . . . . . . . . -40C to +125C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C Voltage on Any Pin with respect to GND . . . . . . . . . . -0.3V to +6.5V DC Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mA
Thermal Information
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . -40C to +85C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. For guaranteed specifications and test conditions, see Electrical Specifications. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions.
Electrical Specifications
SYMBOL BIAS VDD
Over the recommended operating conditions unless otherwise specified. TEST CONDITIONS MIN (Note 4) TYP MAX (Note 4) UNITS
PARAMETER
Supply Voltage Range
VTHVDD = 4.64V, 4.38V, 3.09V, 2.92V, 2.63V VTHVDD = 2.32V, 2.19V, 1.67V, 1.58V
1.8 1.8 215 200 175 160
5.5 2.75 400 350 325 300
V V nA nA nA nA
IDD
Supply Current (RESET, RESET open) VDD = 5.0V, VTHVDD = 4.64V, 4.38V VDD = 3.3V, VTHVDD = 3.09V, 2.92V, 2.63V VDD = 2.5V, VTHVDD = 2.32V, 2.19V VDD = 1.8V, VTHVDD = 1.67V, 1.58V
VOLTAGE THRESHOLD VTHVDD Falling Fixed VDD Voltage Trip Point ISL88001, 88002, 88003Ix346, TA = +25C ISL88001, 88002, 88003Ix346 ISL88001, 88002, 88003Ix344, TA = +25C ISL88001, 88002, 88003Ix344 ISL88001, 88002, 88003Ix331, TA = +25C ISL88001, 88002, 88003Ix331 ISL88001, 88002, 88003Ix329, TA = +25C ISL88001, 88002, 88003Ix329 ISL88001, 88002, 88003Ix326, TA = +25C ISL88001, 88002, 88003Ix326 ISL88001, 88002, 88003Ix323, TA = +25C ISL88001, 88002, 88003Ix323 ISL88001, 88002, 88003Ix322, TA = +25C ISL88001, 88002, 88003Ix322 ISL88001, 88002, 88003Ix317, TA = +25C ISL88001, 88002, 88003Ix317 ISL88001, 88002, 88003Ix316, TA = +25C ISL88001, 88002, 88003Ix316 VTHVDDHYST TVTHVDD Hysteresis at VDD Input VTHVDD Temperature Coefficient 4.570 4.500 4.327 4.262 3.038 3.000 2.890 2.850 2.598 2.559 2.292 2.257 2.164 2.131 1.650 1.625 1.561 1.537 1 0.48 1.580 1.670 2.190 2.320 2.630 2.925 3.075 4.380 4.625 4.681 4.750 4.433 4.498 3.112 3.150 2.960 3.000 2.662 2.701 2.348 2.383 2.216 2.249 1.690 1.715 1.599 1.623 V V V V V V V V V V V V V V V V V V % mV/C
5
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003
Electrical Specifications
SYMBOL RESET / RESET VOL Reset Output Voltage Low VDD < VTHVDD, for ISL88001 VDD < VTHVDD, Sinking 0.5mA for ISL88002 VDD > VTHVDD, for ISL88003 VOH Reset Output Voltage High VDD > VTHVDD, for ISL88001 VDD > VTHVDD, Sourcing 0.5mA, ISL88002 VDD < VTHVDD, for ISL88003 tRPD tPOR CLOAD NOTE: 4. Parts are 100% tested at +25C. Temperature limits established by characterization and are not production tested. VTH to Reset Asserted Delay POR Timeout Delay Load Capacitance on Reset Pin 140 0.2 0.2 0.2 VDD - 0.4 VDD - 0.2 VDD - 0.2 VDD - 0.4 VDD - 0.2 15 200 5 260 0.40 0.40 0.40 V V V V V V s ms pF Over the recommended operating conditions unless otherwise specified. (Continued) TEST CONDITIONS MIN (Note 4) TYP MAX (Note 4) UNITS
PARAMETER
Pin Description
RST
The ISL88003 push-pull RST output is set to VDD (HIGH) whenever the device is first powered up or VDD falls below its respective minimum voltage sense level.
to a P/C if this voltage is less than the preset voltage trip point. The reset signal prevents system operation during a power failure or brownout condition. This reset signal remains asserted until VDD exceeds the voltage threshold setting for the reset time delay period tPOR. See Figure 2.
VDD VDD RPU* ISL88001 ISL88002* ISL88003 VDD
RST
The RST output functions identically to the complementary RST output. On the ISL88001, this is a push-pull output. On the ISL88002, it is an open drain output that is pulled to GND (LOW) when reset is asserted. Suggested pull-up RST resistor values are in the range of 5k to 100k.
RESET OUTPUT
RESET INPUT
P/C
VDD
The VDD pin is the power supply terminal. The voltage at this pin is compared against an internal factory-programmed voltage trip point, VTHVDD. A reset is first asserted when the device is initially powered up to ensure that the power supply has stabilized. Thereafter, reset is again asserted whenever VDD falls below VTHVDD. The device is designed with hysteresis to help prevent chattering due to noise.
GND *Necessary for ISL88002 GND
FIGURE 1. TYPICAL APPLICATION DIAGRAM
Power-On Reset (POR)
Applying power to the ISL88001, ISL88002, ISL88003 activates a POR circuit, which asserts reset once VDD = 1 V. (i.e. RST goes LOW). This provides several benefits: * It prevents the system microprocessor from starting to operate with insufficient voltage. * It prevents the processor from operating prior to stabilization of the oscillator. * It ensures that the monitored device is held out of operation until internal registers are properly loaded. * It allows time for an FPGA to download its configuration prior to initialization of the circuit.
Principles of Operation
The ISL88001, ISL88002, ISL88003 devices provide a low power, high accuracy solution for those voltage monitoring applications needing supply voltage supervision with power reset control. By integrating these features into small 3 Ld SC-70 and 3 Ld SOT-23 packages and consuming as little as 160nA of supply current, these devices can lower system cost and reduce board space requirements.
Low Voltage Monitoring
During normal operation, the ISL88001, ISL88002, ISL88003 devices monitor the voltage level of VDD. The device asserts a reset signal (RST = LOW or RST = HIGH)
6
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003
VTH/VPOR VDD 1V tPOR tRPD tPOR
RST
FIGURE 2. VOLTAGE MONITORING TIMING DIAGRAM
The reset signal remains asserted until VDD rises above the minimum voltage sense level for time period tPOR. This ensures that the VDD voltage has stabilized. Optional VDD de-coupling capacitance can be added to filter transients if needed.
See Figures 13 and 14 illustrating the available evaluation platform, ISL88001/2/3EVAL1Z. This evaluation board is shipped with the many released variants loosely packed and the 4.6V threshold variants mounted for immediate evaluation.
Parametric Performance
VDD VDD VDD
RST RST
RST
FIGURE 3. ISL88001 RST tPOR ~144ms
FIGURE 4. ISL88002 RST tPOR ~155ms, RPU = 5k
7
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003 Parametric Performance (Continued)
VDD
RST
FIGURE 5. ISL88003 RST tPOR ~145ms
FIGURE 6. ISL88003 tPRD ~26s
4.75
2.96
4.70 4.6V VTHVDD (V) 2.9V VTHVDD (V)
2.94
4.65
2.92
4.60
2.90
4.55
2.88
4.50
-40
-20
0
25
50
85
125
2.86
-40
-20
0
25
50
85
125
TEMPERATURE (C)
TEMPERATURE (C)
FIGURE 7. ISL8800x 4.6V VTHVDD vs TEMPERATURE
FIGURE 8. ISL8800x 2.9V VTHVDD vs TEMPERATURE
2.23
1.58 1.58 1.58V VTHVDD (V) 1.57 1.57 1.56 1.56 1.55
2.21 2.2V VTHDD (V)
2.19
2.17
2.15
2.13
-40
-20
0
25
50
85
125
-40
-20
0
25
50
85
125
TEMPERATURE (C)
TEMPERATURE (C)
FIGURE 9. ISL8800x 2.2V VTHVDD vs TEMPERATURE
FIGURE 10. ISL8800x 1.58V VTHVDD vs TEMPERATURE
8
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003 Parametric Performance (Continued)
1.015 1.010 NORMALIZED tPOR 1.005 1.000 0.995 0.990 0.985 NORMALIZED IDD 3.0
2.5
2.0
1.5
1.0
0.5 -40 -20 0 25 50 TEMPERATURE (C) 85 125
-40
-20
0
25
50
85
125
TEMPERATURE (C)
FIGURE 11. ISL8800x NORMALIZED +25C tPOR vs TEMPERATURE
FIGURE 12. ISL8800x NORMALIZED +25C IDD vs TEMPERATURE
ISL88001/2/3EVAL1Z Evaluation Platform
VDD
1k
ISL88001
ISL88002
ISL88003
GND RST1 RST2 RST3
FIGURE 13. ISL88001/2/3EVAL1Z SCHEMATIC
FIGURE 14. ISL88001/2/3EVAL1Z PHOTOGRAPH
9
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003 Small Outline Transistor Plastic Packages (SC70-3)
0.20 (0.008) M C L b C VIEW C
P3.049
3 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE INCHES SYMBOL MIN 0.031 0.000 0.031 0.009 0.009 0.004 0.004 0.071 0.071 0.045 MAX 0.043 0.004 0.039 0.016 0.014 0.007 0.007 0.087 0.094 0.053 MILLIMETERS MIN 0.80 0.00 0.80 0.25 0.25 0.10 0.10 1.80 1.80 1.15 MAX 1.10 0.10 1.00 0.40 0.35 0.18 0.16 2.20 2.40 1.35 6 6 3 3 4 NOTES -
6 C L 1
5
4 C L E E1
A A1 A2 b b1
2
3
e e1 D C L C
c c1 D E E1
SEATING PLANE -C-
A
A2
A1
e e1 L
0.0256 Ref 0.0512 Ref 0.010 0.018
0.65 Ref 1.30 Ref 0.26 0.46
0.10 (0.004) C
L1 L2
0.017 Ref. 0.006 BSC 0 3 0.004 0.004 0.010 8
0.420 Ref. 0.15 BSC 0 3 0.10 0.15 0.25 8
WITH PLATING c
b b1 c1
N R R1 NOTES:
5
Rev. 0 11/06
BASE METAL
1. Dimensioning and tolerances per ASME Y14.5M-1994.
4X 1 R1 R GAUGE PLANE SEATING PLANE L C 4X 1 VIEW C L1
2. Package conforms to EIAJ SC70 and JEDEC MO-203AA. 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. 4. Footlength L measured at reference to gauge plane. 5. "N" is the number of terminal positions. 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only.
L2
10
FN6174.0 March 26, 2008
ISL88001, ISL88002, ISL88003 Small Outline Transistor Plastic Packages (SOT23-3)
0.20 (0.008) M C L b C VIEW C
P3.064
3 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE INCHES SYMBOL MIN 0.035 0.001 0.035 0.015 0.012 0.003 0.003 0.110 0.083 0.047 MAX 0.044 0.004 0.037 0.020 0.018 0.007 0.005 0.120 0.104 0.055 MILLIMETERS MIN 0.89 0.013 0.88 0.37 0.30 0.085 0.08 2.80 2.10 1.20 MAX 1.12 0.10 0.94 0.50 0.45 0.18 0.13 3.04 2.64 1.40 NOTES 6 6 3 3 4 5 0.25 8 Rev. 1 11/06 NOTES: 1. Dimensioning and tolerance per ASME Y14.5M-1994. 2. Package conforms to EIAJ SC-74 and JEDEC MO178AB.
6 C L 1
5
4 C L E E1
A A1 A2 b b1
2
3
e e1 D C L C
c c1 D E E1
SEATING PLANE -C-
A
A2
A1
e e1 L
0.0374 Ref 0.0748 Ref 0.016 0.024 Ref 0.010 Ref 3 0.004 0.004 0 0.010 8
0.95 Ref 1.90 Ref 0.21 0.41
0.10 (0.004) C
L1 L2
0.60 Ref 0.25 Ref 3 0.10 0.10 0
WITH PLATING c
b b1 c1
N R R1
a
BASE METAL
4X 1 R1 R GAUGE PLANE SEATING PLANE L C 4X 1 VIEW C L1
3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. 4. Footlength L measured at reference to gauge plane. 5. "N" is the number of terminal positions. 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only 8. Die is facing up for mold die and trim-form.
L2
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 11
FN6174.0 March 26, 2008

▲Up To Search▲

Price & Availability of ISL88001IE31Z-T

	To Download ISL88001IE31Z-T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .